A pressure transmitter and a controller both list a 4–20 mA interface. The transmitter's data reaches the controller, but the displayed pressure is wrong. The electrical signal can be present while the two devices assign different physical values to it.
To interpret a linear current signal, the receiver needs the physical values assigned to 4 mA and 20 mA, their units and the pressure reference. It also needs the device's defined behavior outside normal operation. A matching interface label does not supply those settings.
For manufacturers publishing English specifications, the useful content connects the signal to its configured measurement range and supporting document. That gives overseas buyers and AI-assisted comparisons a more complete source than “output: 4–20 mA.”
Define the transfer relationship
NI's guide to scaling 4–20 mA sensor data explains a linear scale from current to a measured quantity. For a transmitter configured with a linear output, a convenient expression is:
Pressure = LRV + ((current in mA − 4) / 16) × (URV − LRV).
Here, LRV is the configured lower range value and URV the configured upper range value, expressed in the same pressure unit and reference. The sixteen-milliamp interval comes from 20 − 4. If a data system stores current in amperes, the numerical current inputs must use the corresponding ampere scale.
This is a relationship for an identified linear configuration. Do not apply it blindly to a square-root extraction, reverse action or other configured function. The product manual and actual configuration determine the relationship.
One current can represent different pressures
Consider two fictional linear configurations, both using gauge pressure in bar. Configuration A maps 4 mA to zero bar and 20 mA to ten bar. Configuration B maps 4 mA to minus one bar and 20 mA to nine bar.
| Current | Configuration A: 0 to 10 bar gauge | Configuration B: −1 to 9 bar gauge |
|---|---|---|
| 4 mA | 0 bar | −1 bar |
| 12 mA | 5 bar | 4 bar |
| 20 mA | 10 bar | 9 bar |
At 12 mA, a receiver using A's scale for a transmitter configured as B will display a value one bar above the value assigned by B's scale. The current alone cannot tell the receiver which scale is intended.
These are invented arithmetic cases, not operating instructions or a selection of a real transmitter. They illustrate why configuration belongs with the signal specification.
The sensor's physical measurement limits, the selected output range and a website's catalogue range can also be different. A configurable transmitter might be offered across several sensor ranges. A generic product-family page should not imply that every ordering code covers every listed interval.
Preserve the pressure reference and units
Gauge pressure, absolute pressure and differential pressure refer to different quantities. A number in bar without its reference can be ambiguous even if the current scaling is otherwise correct. A differential-pressure transmitter may also be used in a wider application that introduces another conversion or calculation.
Keep the reference in the product variant and configuration record. If an English comparison converts units, retain the original range and reference so a reviewer can reconstruct the conversion. Unit conversion does not turn gauge pressure into absolute pressure.
Avoid product tables that compress every variant into a single “0–10 bar, 4–20 mA” cell when the actual quotation identifies a different range or reference. The supplier's approved ordering and configuration documents should settle the claim.
The receiver needs this information too. A correct instrument label and a correct webpage do not prove that the installed controller was configured from them.
Keep normal measurement, saturation and alarm behavior apart
A real transmitter can define output behavior for conditions beyond normal measurement, including saturation or diagnostic alarms. Those meanings are product- and configuration-specific. An out-of-range current should not automatically be converted by the normal linear formula and displayed as an ordinary pressure.
Emerson's Rosemount 4051S manual treats output configuration, diagnostics, calibration and alarm behavior in separate sections. That structure is a useful reminder that one interface label does not describe the complete device behavior.
This article does not prescribe universal alarm-current thresholds. Use the current manual for the actual model, selected settings and applicable system requirements. A threshold copied from another transmitter can look plausible and still be wrong for the product being supplied.
For an English catalogue, identify where the buyer can find the supported alarm and diagnostic behavior. If it varies by option, keep that option visible. Do not market a generic analog interface as a promise that a receiver will safely detect every fault.
Distinguish signal presence from complete system performance
A current loop has electrical requirements as well as a transfer function. NI's current-loop fundamentals discusses the components and operating conditions of a loop. Those details matter when checking a real transmitter and receiving input.
The information needed for a selection can include supply requirements, load limits, input characteristics, wiring arrangement and applicable installation requirements. Their actual values belong to the selected products. This article does not supply a wiring design or a hazardous-area installation procedure.
A correct scale also does not establish the full measurement uncertainty or dynamic response. The transmitter, receiver and application can contribute separate effects. A receiver that converts 12 mA to the intended number has passed a scaling check, not every pressure-measurement acceptance criterion.
Keep those acceptance objects distinct in the project record. Otherwise a successful communication check can be promoted into a much broader performance claim.
Give the buyer a complete configuration row
A practical publishing record can identify the exact model and ordering option, physical pressure reference, configured lower and upper values, units, output function, current endpoints and location of the applicable diagnostic documentation.
For a family containing configurable variants, separate fixed product capabilities from the configuration agreed for an order. A sample configuration should be labeled as an example. Do not let a screenshot from a demonstration unit become the default setting claimed for every shipment.
Provide a revision-controlled technical source and a human route for confirming the quoted configuration. A public inquiry form can gather the buyer's required range and reference without pretending that a chatbot has approved the application.
Xindar's manufacturing website and buyer-content work can help make these distinctions readable on an English supplier site. Its confirmed inquiry scope is an inquiry path with human handoff. That does not establish automatic engineering selection, exception approval or a commitment to write an order into a CRM.
Test interpretation before publishing a broad claim
For a content review, prepare a labeled fictional range and ask another reviewer to calculate the values assigned to 4, 12 and 20 mA. Then change the lower range value while keeping the span the same. The reviewer should identify the changed mapping rather than reuse the first result.
Add a signal identified by the source as a diagnostic condition. The expected editorial answer should point to the applicable diagnostic definition rather than convert it into an ordinary pressure using the teaching formula.
These are document-interpretation checks. A real commissioning or calibration procedure requires the actual equipment, authorized method, qualified personnel and its own evidence. Do not describe a worked example as a physical test.
Questions worth asking before a technical comparison
Does 4 mA always mean zero pressure?
It commonly represents the configured lower value of a linear measurement interval. That physical value need not be zero. Read the actual configuration, units and reference.
Can I use the same scale for every 4–20 mA sensor?
No. The physical quantity, endpoint assignments and configured output function can differ. Even two pressure transmitters with the same electrical interface may need different scaling.
Does a valid current prove the pressure is accurate?
It establishes only the observed electrical quantity under the conditions of the check. Correct scaling, instrument performance, installation and the application require further evidence.
For the next quotation, ask the supplier and receiving-system owner to identify the same two endpoint values in the same pressure unit and reference. Resolving that small configuration record is more useful than comparing another row of identical “4–20 mA” labels.