All insights
XINDAR INSIGHT

Read the Stress Ratio Behind a Fatigue-Life Claim

Recalculate stress range,amplitude,mean and ratio,then connect fatigue-life claims to specimen conditions,curve axes and runout records.

Sources checked November 17, 2026

An overseas buyer sees two metal-component datasheets. Each advertises one million cycles at a maximum stress of 100 MPa. One test reverses between tension and compression. The other cycles between two tensile stresses. The same peak value describes different loading histories.

A useful fatigue claim connects the cycle count to the stress definition, stress ratio, specimen, material condition and failure criterion. The test's observation limit also matters. A specimen that reaches the planned stopping point carries different information from a specimen that fails there.

The worked numbers below are fictional teaching examples. They demonstrate how to read a report and prepare an engineering enquiry. Actual component acceptance depends on the applicable specification, test evidence and the responsible engineering review.

Define the stress cycle before comparing life

For a stated scalar stress history, identify the maximum stress, σmax, and minimum stress, σmin. Tensile stress is positive in the uniaxial examples used here. Compression is negative. Record the stress component and sign convention with the values.

Four useful quantities follow from those extrema.

QuantityDefinition for the cycle
Stress range, Δσσmax − σmin
Stress amplitude, σa(σmax − σmin) / 2
Mean stress, σm(σmax + σmin) / 2
Stress ratio, Rσmin / σmax, when σmax is nonzero

These definitions describe the cycle's size and position. A fully reversed cycle has equal tensile and compressive extrema, zero mean stress and R = −1. A cycle that moves between zero and a positive tensile maximum has R = 0. COMSOL's fatigue documentation illustrates these quantities and explains that source fatigue data may use either maximum stress or amplitude as its stress measure. COMSOL Fatigue Module User's Guide, page 51

The scalar qualification matters. A report may use nominal axial stress, local stress or another declared measure. Ask which quantity appears in the calculation and which appears in the test curve. The same unit, MPa, can accompany several stress definitions.

Work through two cycles with the same peak

The first fictional cycle ranges from −100 MPa to +100 MPa. Its range is 200 MPa, amplitude is 100 MPa, mean is zero and ratio is −1.

The second ranges from +10 MPa to +100 MPa. Its range is 90 MPa, amplitude is 45 MPa, mean is 55 MPa and ratio is 0.1.

Fictional cycleMaximum MPaMinimum MPaRange MPaAmplitude MPaMean MPaR
Fully reversed example100−1002001000−1
Tensile example100109045550.1

Both have the advertised 100 MPa peak. Their amplitudes differ by 55 MPa, and their mean stresses differ by 55 MPa. The arithmetic establishes those differences. Estimating the resulting lives requires appropriate material data and a justified treatment of the loading conditions.

A buyer can resolve an ambiguous claim with a short request. Ask for the maximum and minimum values, the ratio, the plotted stress quantity and the underlying test report. Those fields allow an engineer to identify what loading the stated cycle count actually describes.

For an export catalogue, place the ratio close to the life value. A reader copying a single table row should carry the loading condition into the enquiry. A footnote several pages away is easier to lose during quotation or translation.

Read the axes and the curve conditions

An S–N curve relates a stated stress measure to cycles associated with the stated fatigue criterion. Read the vertical-axis definition before extracting a point. Also inspect units, scale, material condition, loading ratio and the meaning of the displayed curve.

For example, ZwickRoell's illustrated Woehler curve uses nominal stress amplitude on its stress axis. Its explanation also identifies crack or fracture as possible failure criteria in the discussed finite-life region. A buyer using a particular report must find the criterion selected for that report. ZwickRoell S–N curve guide

In the two fictional cycles, a vertical coordinate labelled amplitude would be 100 MPa for the first cycle and 45 MPa for the second. A coordinate labelled maximum stress would be 100 MPa for both. The axis label therefore changes how the numbers are entered or compared.

Read the curve's statistical description as well. A supplied line may represent a fitted relationship or a stated reliability basis. Ask the originator what the line means, which observations support it and how its uncertainty was handled. Keep that explanation attached to any value extracted for a purchase decision.

Keep the specimen and service conditions attached

ASTM E466-21's public scope describes constant-amplitude, axial force-controlled testing of metallic specimens in air at room temperature, with predominantly elastic strains. It distinguishes its specimen scope from full-scale component testing. Its public significance section says design application needs realistic simulation of service conditions or a clearly defined way to account for them. ASTM E466-21 public scope

A buyer can use that boundary to structure the next enquiry. Identify the tested specimen and compare it with the ordered part's geometry, manufacturing condition and operating environment. Ask the responsible engineer how the proposed design use accounts for any differences.

Consider a fictional catalogue for a machined bracket. The supplier attaches a smooth-specimen fatigue chart for the alloy. The buyer's drawing adds a hole, a particular finish and an assembly preload. The chart belongs in the technical evidence package together with an explanation of its applicability to the bracket.

The supplier can identify the report origin, material condition and specimen preparation. The engineering team can then assess the component and the declared load history. The catalogue becomes more useful when it preserves those responsibilities and provides a route to the supporting records.

Record a runout as an observation limit

Suppose a fictional test programme plans to stop each specimen after two million cycles if the declared failure criterion has not occurred. Three specimens fail earlier. Two reach the stopping point without that failure.

Fictional specimenObserved cyclesDeclared failure observedRecord type
F1700,000YesFailure observation
F21,000,000YesFailure observation
F31,400,000YesFailure observation
F42,000,000NoRunout at planned stopping point
F52,000,000NoRunout at planned stopping point

For F4 and F5, the recorded information is survival to the observation limit under the test's criterion. Their later failure cycles remain unknown. The data file needs both the observed cycles and the event status.

NIST explains right-censored reliability data using tests that end at a fixed observation time, leaving some units without observed failures. Applying that concept to a planned cycle-count stopping point preserves the distinction in this example. The data retains three observed failures and two right-censored observations. NIST explanation of censoring

An analyst fitting a fatigue relationship needs a method appropriate to the test design and censoring. The five rows alone provide the recorded outcomes. They leave estimation of a population curve, uncertainty and service reliability to a defined analysis.

Record why each test stopped. A planned runout, equipment interruption and an unrelated specimen event can carry different implications for analysis. The originator should retain that reason with the cycle count and the selected failure criterion.

Build an evidence table that survives quotation

ASTM E468/E468M-23a's public description emphasizes material, specimen and test information when presenting constant-amplitude fatigue results. Its stated field covers constant-force-amplitude axial, bending or torsion tests of metallic materials in air at room temperature. The public page provides the scope used here. ASTM E468/E468M-23a public description

The following is an editorial enquiry checklist. The applicable purchased standard and contract determine the actual reporting and acceptance requirements.

Evidence fieldDetail to request
Material identityGrade, heat or batch link, heat treatment and other relevant condition
Test objectSpecimen geometry, preparation, surface condition and report identification
LoadingMethod, stress quantity, maximum, minimum, ratio, waveform and frequency
EnvironmentTemperature, atmosphere and other declared test conditions
EndpointFailure criterion, stopping rule and individual stop reasons
ResultsPer-specimen cycles, event status, curve definition and analysis method
Design useEngineering explanation connecting the evidence to the ordered component
TraceabilityReport revision, issuing organization and the party resolving technical questions

Every field needs a source or an explicit pending state. This makes a preliminary quotation workable even while an engineer is reviewing applicability. The commercial team can identify the open condition and carry it into the offer and order acknowledgement.

Publish the conditions an overseas buyer needs

A manufacturer preparing English technical content can place a short, qualified summary beside the product specification. Link the supporting report where disclosure is permitted. Retain its title and revision so a buyer can request the correct document through the enquiry route.

Where the evidence concerns a specimen, state that test object. Where the claim refers to a component qualification, identify the component revision and applicable test basis. Keep the number, stress definition, ratio and endpoint together in the public summary.

Xindar's manufacturing export work covers technical-content presentation, website enquiry paths and human handoff. A project can use the evidence table above to organize material supplied by the manufacturer and route unresolved engineering questions to the responsible person. Xindar manufacturing export services

A practical review can follow five steps.

  1. Locate the original report and confirm the tested material and object.
  2. Recalculate range, amplitude, mean and ratio from the stated extrema.
  3. Match the quoted life to the curve's stress axis and loading conditions.
  4. Preserve each specimen's endpoint, stop reason and event status.
  5. Obtain the engineering disposition for the ordered part and its intended service.

The completed review should leave a buyer with a traceable claim and a clear list of conditions still requiring agreement. Those records give the technical enquiry somewhere concrete to go.

Questions buyers ask

Does a million-cycle claim include its stress condition automatically?

Read the attached report or specification. A cycle count becomes interpretable when the loading quantity, extrema or ratio, test object and failure criterion accompany it.

What does R = −1 describe?

For the uniaxial sign convention used here, the minimum stress is the negative of the maximum. The cycle is fully reversed and its mean is zero.

Can maximum stress and amplitude use the same value?

They coincide for the fully reversed fictional example because its minimum is −100 MPa. In the tensile example, the maximum is 100 MPa and the amplitude is 45 MPa. Calculate from the actual extrema.

How should a runout appear in a spreadsheet?

Retain the cycles reached, an event-status field and the stopping reason. For a planned stop without the declared failure, preserve the observation limit so the analyst can handle censoring explicitly.

Which person should approve use of a specimen curve for a component?

The project needs a named, responsible engineering reviewer working from the applicable design and acceptance requirements. The supplier's evidence package should make the specimen conditions and component differences available for that review.

Back to insightsMarkdown version